Stock Number: 232192
Make: WackerNeuson
Model: WK HI400HD D
Year: 2013

Stock Number: EQU005272
Make: CAT
Model: C5000-LE
Year: 2011

Stock Number: 206419
Make: Jungheinrich
Model: ETR345-36V
Year: 2012

Stock Number: EQC013552
Make: Hyster
Model: E30Z
Year: 2010

Stock Number: 1-16-232262
Make: Spyder
Model: URW376
Year: 2014

Stock Number: 2-18-UEF80
Make: Misc
Model: FORKS

Caterpillar Forklifts New York

Caterpillar Forklifts New York

Driving a forklift is a lot more complicated compared to driving a vehicle. A forklift operator must be highly trained and skilled in the operation of a forklift. Operating a forklift requires a high level of attentiveness. The Occupational Safety and Health Administration reports that 85 people die in forklift-related mishaps per year. Around 35,000 people are hurt every year in lift truck mishaps. Nearly half of operator deaths are caused by a lift truck tip over.

To prevent tip overs, it is important that operators know how to correctly estimate the weight of a load. In the construction industry, the weight of a load is normally posted right on the load. If the load consists of cubes containing 90 concrete blocks and a concrete block weighs 16 kilograms, the whole weight of the load would be approximately 1,360 kilograms. If a load is wet, the driver must take additional weight into consideration.

It is dangerous for drivers to make poorly informed guesses about the real load weight and whether the lift truck can handle it. If an operator cannot be sure about the load weight, he should request assistance from the supervisor.

Failure to pull up near enough to a building or lift a load utilizing an extended boom can be another cause of tip overs. To avoid tipping lift truck, it is essential to use the load chart. Even when a forklift does not actually tip over, a mishap has occurred whenever the back wheels come off the ground. This means the limitations of the forklift have been exceeded. Though damage may not be obvious, the back axle can have sustained broken upon hitting the ground.

It is even possible for forklifts to tip even when not carrying a load. Unloaded forklifts could tip just after a driver has placed a load on scaffolding using an extended boom. If the operator reverses the forklift and turns suddenly while bringing the boom down, the center of gravity would be pushed to the edges of the forklift and could result in a tip over. A driver must always use the joysticks to be able to retract and lower the fork.

  • Manitou Forklifts New York
    Frequent inspections can really help to reduce forklift maintenance and save you copious amounts of money in the long-run. The standing ... More
  • Toyota Forklifts New York
    Toyota lift trucks can fill nearly each and every one of your material handling requirements from improved ergonomics, better ... More
  • Komatsu Forklifts New York
    Fleet managers could plan for the unplanned, ramp up on safety measures and overall productivity and lessen costs with several simple ... More
  • Liftking Forklifts New York
    The forklift manufacturer Manitex LiftKing is major North American maker of material handling products. Their complete lineup of ... More
  • Taylor Forklifts New York
    Lift trucks or forklifts are powered industrial trucks that are usually utilized in the transportation and lifting of materials for ... More
  • Daewoo Forklifts New York
    Start-up of the forklift business A national expansion of the industrial equipment industry was encouraged by Korea during the late ... More
  • Xtreme Telehandlers New York
    The XR842 roller boom telehandler has a forward reach of 28 feet, 10 inches, a lift height of 41 feet, 5 inches and a lift capacity of ... More
  • Hyster Forklifts New York
    The comprehensive and responsive "after-sale" support offered by Hyster is the most thorough within the material handling industry. ... More

Caterpillar Forklifts New York

Short Story: